Removing Stains from a Limestone Fireplace Hearth in Chelmsford

The UK has been experiencing an increasing amount of rain over the last few years and this has resulted in quite a few areas being flooded. One of those areas is the old city of Chelmsford in the middle of Essex which is prone to flooding due to the rivers Cam and Chelmer that run through the town.

Limestone Fireplace Before Flood Stain Removal Chelmsford

I was asked to visit a property in the town that had been flooded over winter and the red dye in the carpet that was lying on the floor adjacent to their lovely Limestone Fireplace had stained the hearth in several places but primarily around the edges.

Limestone Fireplace Showing Red Dye Staining Chelmsford

The fire place had never been sealed and because of this the stone had sucked up the flood water like a sponge. They had drying equipment installed and as the moisture evaporated the red staining became more and more evident. Since then several companies had been to try and remedy the problem and each one was unsuccessful. The couple contacted us, and we went to assess the problem fully equipped to carry out the work.

Cleaning a Dye Stained Limestone Fireplace Hearth

Had the Fireplace been sealed we our first task would have been to remove to ensure we would have no issues sealing the fireplace later. In this case however that wasn’t an issue, so we were able to move straight onto cleaning up the stone using a set of diamond encrusted hand-held burnishing blocks. We started with the coarsest block (50 grit) and rubbed the stone with a bit of added water as lubrication, before wet vacuuming away the excess residue. This process was then repeated with progressively finer blocks (100, 200 and 400 grit), and the hearths were given a final rinse with fresh water.

The burnishing blocks are excellent tools to remove scratches and marks from tile and stone and did a good job of removing the red dye from around the hearth. They also took care of some marks that had appeared where the owner had placed a couple of slate tiles on the flat part of the hearth.

Limestone Fireplace Showing Rust Stain Spots Chelmsford

Along with these marks were some corrosion spots where a metal ornament had been sitting on the hearth for several years. I treated these with Tile Doctor Rust Away which is a specialist product for removing rust stains from tile and stone after a few applications the stain was gone.

Limestone Fireplace Showing Rust Stain Spots Chelmsford

Sealing a Limestone Fireplace Hearth

After we had cleaned the fireplace up to the satisfaction of the client we used a smail dryer to dry everything out so that we could finish the job and seal the fireplace the same day. Once the stone moisture levels were at the correct level the Limestone Fireplace was sealed using three coats of Tile doctor Ultra-Seal leaving twenty minutes between coats.

Ultra-Seal is a no-sheen product that impregnates the pores of the stone protecting from within without changing the look of the stone thereby leaving it with a natural appearance. I’m please to say our efforts paid off and the Limestone Fireplace and Hearth is now stain free and looking like new.

Limestone Fireplace After Rust Stain Removal Chelmsford Limestone Fireplace After Flood Stain Removal Chelmsford

 

Source: Fireplace Cleaning and Restoration Service in Chelmsford, Essex

Restoring Flood Damage to a Limestone Fireplace

Morecambe is a large town on Morecambe Bay in Lancashire, and is a tourist hotspot within the region – particularly amongst beach goers during the summer. However, due to its location of being right next to the coast and near to the River Lune, Morecambe is an area which is commonly affected by flash flooding. Just last year there were several episodes of severe flooding.

This flooding has a big impact on houses and businesses – the damage water can cause can come as quite a surprise if you have not experienced it before. I recently visited to a business in Morecambe which had been affected by flooding. The business was, in fact, a fireplace showroom and a pair of the Limestone fireplace hearths on display had been stained by the water.

Floor Damaged Limestone Fireplace Hearth Before Cleaning Floor Damaged Limestone Fireplace Hearth Before Cleaning

We were asked to remove the water marks left by the flooding. One of the hearths has been in use as a test model, with a coal burner installed, and it hadn’t been cleaned properly in some time. As you can imagine, there were more problems than just the water stains to overcome! Both hearths would require a deep clean and fresh seal.

Cleaning Stained and Dirty Limestone Fireplaces

To begin, we applied Tile Doctor Oxy-Gel to the hearths. This product is a specially formulated, alkaline-based degreaser and cleaner. As it comes in a gel form, not a liquid, Oxy Gel can be brushed into vertical surfaces and left to soak, without risk of it either disappearing into the Limestone or, even worse, trickling down the side of the surface. We would not want it coming into contact with the carpet, for instance.

We left the Oxy-Gel to dwell for a short period on one hearth while we worked on the other, applying the same treatment. After around twenty-five minutes we rinsed off the gel with clean water and then extracted any excess moisture with the use of a wet vacuum.

This process did a good job of cleaning the Limestone, but more work was required to restore its appearance, so the hearths were polished using a set of diamond encrusted hand held burnishing blocks. We started with the coarsest block (50 grit) and rubbed the stone with a bit of added water as lubrication, before wet vacuuming away the excess residue. This process was then repeated with progressively finer blocks (100, 200 and 400 grit), and the hearths were given a final rinse with fresh water.

There were some odd ring marks on one of the Limestone hearths that we couldn’t remove. Thankfully, the owner put our minds to rest on this problem, as he said they were there when he initially purchased the stone over 20 years ago. They had been covered with dirt ever since and the customer was surprised, but not shocked, to see them again. I suspect that these marks were caused by the natural mineral deposits within the stone. These should not be seen as a stain, but just a characteristic of the stone – and no amount of cleaning will get these marks out.

We would normally seal a light-coloured stone like this with Tile Doctor Ultra-Seal, as this no-sheen product helps to retain the natural patina of the stone. Alternatively, if we wanted to darken the tone of the Limestone, we would apply Tile Doctor Colour Grow, which is a colour-intensifying, impregnating sealer. Two coats of either sealer would suffice, in this case despite being very pleased with the results of the cleaning, the customer decided that he wanted to take care of sealing of the stone himself.

Floor Damaged Limestone Fireplace Hearth After Cleaning Floor Damaged Limestone Fireplace Hearth After Cleaning

 
 
Source: Fireplace Tile Cleaning and Sealing Service in Lancashire